LEGAL WARNINGS
Except as stated in the warranty, there are no other representatives or warranties related to the
product or its use. THE USER SHALL DETERMINE THE SUITABILITY OF THE PRODUCT FOR THE USER’S
INTENDED USE, AND THE USER ASSUMES ALL RISKS AND LIABILITIES WHATSOEVER IN CONNECTION
THEREWITH. Seller and manufacturer’s only obligation is to repair and or replacement of submersible
light housing as stated below. ALL IMPLIED WARRANTIES ARE HEREBY EXCLUDED, INCLUDING, BUT
NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PUR-
POSE. Neither seller nor the manufacturer shall be liable for any injury loss, or damage whether direct,
incidental, or consequential arising out of the use or inability to use the product.
To reduce the risk of electrical shock, all wiring and junction connections should be made per local
codes. Requirements may vary depending on usage and location.
1
YEAR
WARRANTY
1
GARANTIE
DE 1 AN
2
YEAR
WARRANTY
2
GARANTIE
DE 2 ANS
3
YEAR
WARRANTY
3
GARANTIE
DE 3 ANS
1
YEAR
WARRANTY
1
GARANTIE
DE 1 AN
2
YEAR
WARRANTY
2
GARANTIE
DE 2 ANS
3
YEAR
WARRANTY
3
GARANTIE
DE 3 ANS
The 1 Watt, 12 volt LED Waterfall Light is warrant-
ed against defective materials and workmanship
for a period of 12 months from the date of pur-
chase by the user. Contact the installer or place
of purchase if the 1 Watt, 12 volt LED Waterfall
Light should fail within the warranty period. War-
ranty shall be totally null and void in the event
the 1 Watt, 12 volt LED Waterfall Light is abused,
misused, or used for a purpose other than for
which the product is intended. No warranty
applies to the light bulb used with the housing.
WARNING
It is recommended whenever working in or near water to have all electrical devices
plugged into a ground fault circuit interrupter (GFCI) that has been installed by a
licensed electrician.
COVER TO LIGHT MUST BE TIGHT AT ALL TIMES TO PREVENT ANY LEAKING .
1-Watt 12 Volt
LED Waterfall Light
PACKAGE INCLUDES:
• 1-Watt, 12 Volt LED Waterfall Light
• Plastic Light Stand
Optional Accessories for the 1-Watt
12 Volt LED Waterfall Light (sold separately)
• Interchangeable colored LEDs
(blue, red, green, and yellow)
• Low Voltage Transformer
Installation Instructions
Installing the Light
It is easiest to install and conceal the 1-Watt 12 Volt
LED Waterfall light(s) prior to putting the gravel in
the pond and stream. Find a desirable location for the
light(s). We suggest positioning the light(s) so they are
facing away from the main viewing area. Double-check
to make sure that the ring nut is fastened tightly down
using the supplied lens key. Depending on the instal-
lation, the 1-Watt 12 Volt LED Waterfall light(s) can be
used in or out of water. If being used out of water attach
the light to the stand, if being used in the stream area
the light can be used with the light stand or without.
Simply take the cord and plug into the transformer,
plug in transformer and enjoy! The 1-Watt 12 Volt LED
Waterfall light(s) can also be wired directly into a pre-
existing low voltage lighting system. In order to do this,
cut off the plug on the light and splice directly into the
low voltage wire.
Replacing the Light Bulb
Troubleshooting
• Make sure that the plug is inserted all the way into
the transformer. If light is wired into a low voltage
lighting system make sure all of the connections
are sound.
• Make sure that no water has seeped into light
housing unit.
• Check light bulb.
• Bulb life can be greatly increased by setting timer
on transformer, so the light only operates during
the desired times.
1. Make sure all power is shut off to the light before
changing the bulb. The light housing must be
above water to properly service the light bulb.
2. Unscrew the ring nut from the front of the
light housing unit using the supplied lens key.
3. Remove the glass lens and o-ring from
light housing.
4. Remove the LED bulb.
5. Insert the new bulb.
6. The o-ring and lens can now be installed
back into place. Make sure there is no dirt or
debris on the lens, o-ring and assembly prior
to reassembling.
7. Attach the ring nut onto the light housing.
8. Test to make sure light works.
9. Position light back into pond.
Replacement Parts
Replacement Bulbs for 1-Watt
12 Volt LED Waterfall Light
Made in China
Aquascape, Inc.
St. Charles, IL 60174 • Brampton, ON L6T 5V7
www.aquascapeinc.com
Item #98928.2009
©2012 Aquascape, Inc. • All Worldwide Rights Reserved IDD 09087535-AI 080181
#98370 Red LED Replacement Bulb
#98371 Blue LED Replacement Bulb
#98372 Green LED Replacement Bulb
#98373 Yellow LED Replacement Bulb
#98452 White LED Replacement Bulb
(1 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels